Gas line work is priced differently from ordinary plumbing, and the national guide figures give you a way to sanity check a quote. One guide lists new installation at between $15 and $25 for each linear foot, a whole-job average near $800, and most jobs between $500 and $2,000. This is the price side of gas lines in Temecula. Send the quote form and we pass it to a local plumbing business, which names a price after looking at the job.
All numbers here are a guide taken from published national sources, not Temecula quotes. Distance from the meter, trenching or attic work, the type of pipe, and the permit all shift the result, and a contractor must do gas work in California.
What does it take, money-wise, to run a gas line through a house?
Published per-foot figures put new installation around $15 to $25, extensions of an existing line at $10 to $20, and furnace lines at $20 to $25 per foot. Water heater lines come in lower, near $10 to $18 per foot. For a typical home, complete jobs come to about $800 on average, within a span of $500 to $2,000.
| Job | Guide figure |
|---|---|
| New line, per foot | $15 to $25 |
| Extension of an existing line, per foot | $10 to $20 |
| Water heater line, per foot | $10 to $18 |
| Furnace line, per foot | $20 to $25 |
| Relocation, per foot | $15 to $25 |
| Replacement of a line, per foot | $23 to $35 |
| Typical whole job | average about $800, within $500 to $2,000 |
The same source adds $1,250 to $1,600 for running lines to several rooms inside a house, and $850 to $1,100 for an extra 50 feet from the street to the house. Those are national averages. A line through a finished garage ceiling costs more than one along an open attic joist.
What does fixing a gas pipe cost?
Repairs are priced by the section: one guide puts removing a broken section at $6 to $10 per foot and installing a new section at $10 to $25 per foot. A pressure test runs about $75 to $100, and an inspection costs $50 to $75. Fixing a leak at a fitting is smaller than replacing a corroded run.
When gas is in the air, never hunt for the source. Leave the building first, then phone SoCalGas at 1-800-427-2200 from outside, and dial 911 if there is danger. Touch no switches. Repairs to gas piping are for a contractor and are no weekend project; the rules are explained on the page about who does gas work.
What do gas plumbers charge per hour?
One gas line guide lists plumber hourly rates of about $75 to $130, and a second cost guide has general plumbers at $25 to $200 an hour by experience, averaging near $100. Gas Safe is a register from the United Kingdom with no force in California, where the question is whether the plumber has a California contractor license.
Any job that needs a permit, as gas piping normally does, calls for a California contractor license, and so does any job where labor and materials reach $1,000 or more. Checking falls to you: before work begins, request the license number and search for it on the Contractors State License Board website. The wider price picture is in plumber prices in Temecula.
What does gas pipe cost, and which type should it be?
Pipe makes up only a small share of the total. Flexible corrugated stainless steel tubing is cheaper per foot to buy and quicker to run, while black iron takes more labor, fittings and threading. Pipe size follows from how long the run is and how much the appliances draw, so the plumber chooses it, not you. One appliance commonly gets a flexible line of half an inch.
The article on a 1/2 inch flexible gas line explains where it fits. At an appliance, the short flexible connector is a separate part from the supply pipe, and a new appliance normally gets a fresh connector rather than the old one.
How much does a gas shutoff or earthquake valve cost?
One guide prices a general gas shutoff valve at $210 to $500 installed. An earthquake-actuated shutoff valve is a related job, and we have not found a checked price for it, so get a quote from the plumber. The valve closes the gas supply automatically in strong shaking, and installation is handled by a plumber.
To learn whether a permit applies, phone the City of Temecula Building and Safety division at 951-694-6439, or the county if the parcel is rural. The installation guide and the page on why the valve matters in earthquakes give the how and the why.
What else shows up on a gas quote?
Expect lines for the permit, which one guide puts at $50 to $300 depending on the jurisdiction, the pressure test, appliance hookups at $220 to $350, and shutoff valves. If the meter needs work, the utility usually handles it, and one guide lists $250 to $425 where a meter is installed by someone else. Connecting to the main is listed at $200 to $300.
Ask the plumber to list parts and labor separately and to say what follows if the inspector demands changes. Permits inside Temecula come through the City of Temecula Building and Safety division. Outside the city, in Wine Country, French Valley or Winchester for example, Riverside County applies, while San Diego County handles parcels around Fallbrook, De Luz and Rainbow. Rural lots often run on propane, not piped gas, so the job may be a tank connection, not a utility line.
Common questions
How much does it cost to mend a gas pipe?
A minor repair at a fitting or short section can land near the low end of the per-foot range: $6 to $10 to remove and $10 to $25 to install, plus a $75 to $100 pressure test. A corroded run costs more. The plumber should test once the repair is done, and the price belongs in writing beforehand.
How much is a gas plumber?
Expect hourly rates of about $75 to $130 in a gas-line cost guide, with other guides reporting $50 to $200 an hour for plumbers in general. A permit and a pressure test usually come with gas work and add to the total. Get a written quote and verify the contractor license number.
What do plumbers charge for running a gas line?
One national guide gives about $15 to $25 per foot of new line, with whole jobs from about $500 to $2,000 and an average near $800. Appliance hookups and permits come on top. Long runs, trenching and finished walls raise the price. The plumber's quote is the price that applies.
Does a new gas appliance change the cost?
Yes. A new range, dryer, fireplace or tankless heater may need a bigger line or a shutoff at the appliance, because the pipe has to be sized by the plumber for the total load. Mention every appliance on the line, and check water heater replacement costs if a heater is part of the plan. The home page shows what else we can send a plumber for.
Updated