A burning pilot with cold taps points one of two ways: the main burner never switches on, or it does and the warmth fails to get into the water. Common culprits include the thermostat setting, a tired thermocouple, a faulty gas control valve and sediment build-up. These notes suit a gas tank heater. The bigger picture is on water heater repair in Temecula.
Gas appliances mark a firm limit for do-it-yourself work. Should you smell gas, exit the house and phone SoCalGas at 1-800-427-2200 from the street, or dial 911 if someone is in danger. Strike no flame, touch no switches and keep your phone out of the building until you are clear.
What keeps the burner from firing when the pilot is lit?
On a gas tank heater, the pilot flame heats a safety sensor, and the thermostat inside the gas control tells the main burner when to light. If the control is set too low, if the sensor no longer reads the flame properly, or if the control valve has failed, the pilot stays lit but the burner never opens.
Check the temperature dial on the gas control first. A setting turned to vacation or the lowest mark keeps the burner off. Many manufacturers suggest roughly 120 degrees Fahrenheit for normal use; check your label. Turn the dial up a notch and wait a few minutes to hear the burner light with a soft whoosh. A dial that moves freely and still gives no burner points toward the control valve.
Is the problem sediment, venting or the heater's age?
It can be. Thick scale across the tank bottom makes the burner work harder, stretches heat-up times and can trip safety devices. Poor combustion air or a blocked flue can also shut the burner down for safety. In Temecula, where Rancho Water reports average hardness near 230 to 240 mg/L in the 2020 to 2023 reports, sediment is a real factor.
Flushing a tank heater clears loose sediment, though a heater with years of untouched scale may not recover. Age matters too: a heater at ten or more years with cold water and repeated failures is a replacement candidate. The replacement cost page lists what to weigh. Soot, scorch marks or a smell of exhaust mean you should switch the heater off and call a plumber, since those can point to combustion problems.
Could the thermocouple or thermopile be weak?
Yes, and it is the classic cause when the pilot looks fine. A worn-out thermocouple or thermopile may fail to produce the voltage needed to keep the gas valve open for the main burner, even while it sustains a pilot. The pilot flame itself also has to touch the sensor tip.
A yellow or lazy pilot flame, or a sensor tip coated with soot, can mimic a weak part. A thermocouple is inexpensive, and some owners swap one by following the heater's manual. If you are not comfortable working next to a gas control, hand it to a plumber. The thermocouple replacement guide and the page on repairing a pilot light cover the detail. If a control shows no light at all, read about a Honeywell water heater with no status light.
Could the trouble be the hot water supply rather than the heater?
Sometimes. Cold or lukewarm water can come from a crossed or failing mixing valve, a closed shutoff, a snapped dip tube or a bad faucet cartridge, with the heater itself working well. Try several taps. When some deliver hot water and others stay cold, the heater is most likely fine.
Let the hot tap closest to the heater run for a minute. A hot nearby tap with a cold far-off shower means the issue is distance or a valve along the route. Plastic bits showing in aerators suggest a failed dip tube; see water heater dip tube replacement. A related guide on showers is shower with no hot water.
Which jobs are safe to do yourself?
Owners can read the thermostat dial, make sure the heater's cold-water shutoff and gas supply valve are open, note the colour of the pilot flame and relight it by the instructions printed on the tank. Beyond that, whether it is opening the gas control, altering gas piping or touching the flue, the work belongs to a plumber or the utility.
Gas piping and any job that needs a permit call for a California contractor license, and a water heater replacement generally needs a permit too. Relighting a pilot as the label describes is an owner task. If the flame will not hold after two attempts, stop there. Repeated tries can let gas collect in the cabinet, so pause several minutes between attempts and air out the room.
At what point do you pass this to a plumber?
Phone one if the burner stays off after you turn the dial up, the pilot keeps blowing out, the heater clicks or hums without a flame, there is soot or a gas smell, or the heater is aging and the repair would cost a lot. The plumber tests the thermocouple, the control and the draft.
To arrange that, use the quote page. A visit usually covers gas pressure and venting checks, followed by a replacement part or advice about a new heater. Inside Temecula city limits, permit questions go to Building and Safety at 951-694-6439; rural parcels deal with their county, Riverside or San Diego. Around Fallbrook and nearby areas the gas may be propane or come from another utility, so say so when you call.
Common questions
Why is there no hot water when the pilot is lit?
The pilot runs separately from the main burner. A pilot can burn for months while the burner fails to ignite because of a dial setting, a worn thermocouple or a failed control. Start with the dial, then call a plumber if raising it makes no difference.
Can a thermocouple go bad while the pilot stays lit?
Yes. A weakened thermocouple can generate too little voltage to keep the main gas valve open for firing, even when the flame looks normal. Soot on the sensor tip or a misaligned flame can do the same. Replacing it is a standard repair on most tank heaters.
Is relighting the pilot myself risky?
It can be done safely by following the tank's printed instructions, provided there is no gas smell. If gas is present, do not attempt it. Leave the house and call SoCalGas on 1-800-427-2200 from the street. Never force a control, and give up if the flame fails to stay after two tries.
Could a tankless heater have the same problem?
Tankless units have no standing pilot on most modern models, so the same pilot checks do not apply. They need flow, gas, ignition and a clean heat exchanger. Look at tankless repair for an electric example, and return to the home page for other services.
Updated